In general, the life of a car battery is 2 to 3 years, and the original battery of a new car can be used for more than 3 years. In fact, many new owners have lost their batteries quickly because of some improper use of small habits. When the parking is turned off, forgetting to turn off the lights inside the car is a small mistake that many new owners are likely to make. After a night's consumption of the battery, the battery may be out of power at any time and the car cannot be started. In this case, try charging the battery if conditions permit. If it still doesn't work, the battery may need to be replaced. Try not to use CDs, cigarette lighters and other electrical equipment when the vehicle is not started, and use a variety of vehicle-mounted electrical appliances during driving. â—† Several bad habits of damaging the battery Start the vehicle frequently: Do not exceed 3 seconds each time the engine is started. If the first startup fails, don't rush to start it again. From the working principle of the car, continuous starting of the motor at this time will definitely cause the battery to be over-discharged and damaged. The master suggested that the time interval between re-launch should exceed 5 seconds. Forget the air conditioner before turning off the flame: Most car owners are accustomed to not turning off the air conditioner or letting the air conditioner start automatically after the vehicle starts. This will cause the air conditioning system to start automatically after each time the vehicle's ignition switch is turned on. The consequence is that the vehicle instantaneous power is directly caused. The load is too high, and the battery will cause loss for a long time. The correct habit should be that before reaching the destination, turn off the A/C button and let the cold air blow for a few minutes to ensure the drying inside the air conditioning system and reduce the breeding of bacteria. Then turn off the air conditioner before turning off the flame. After each drive, start the air conditioner again.
1. Material: 65Mn (or T9.
___________________________________________________________________________________________________
Combine Advantage:
1. We have been working internationally
in the area of agricultu al parts and bearings since 2002 and have
excellent knowledge,experience in the agricultural field.
2. We offer over 1000 different spare
parts for a wide range of agricultural machinery, from combine
harvesters, mowers,rakes to balers.They are used for various makes like
John Deere, LAVERDA ,Claas, New Holland and Case/IH.
3. Averagely we add at least five new
items monthly to our production range. This wide supply and quick
development are our big advantages over our competitors
4. [Quality",[honesty"and[service" is our principle, we export to more than 56 countries at present, mostly to Europe.
Specification:
1. Function/Use: Widely used for John Deere, New Holland, Class, Case, Schumacher machinery
2. Feature/Characteristic: Knife assemblies come with heat treated knife connectors, providing maximum stability and strength
3. Advantages: Maximal safety due to rigorous quality checks and test.
4. Superiority: Very Strong, including in the connector area
5. We can supply the Cutter Bar Assembly with wide range length, also can supply all parts
6. Any samples or detailed drawings are welcome here. We have professional engineers to develop new products with you
7. Certificate: CE and ISO9001, Alibaba Trading Assessment
Constitute of knife assembly
Material:
65Mn or T9
Hardness:
HRC50-55, Induction hardening process guarantees long wear
Thickness:
2.00-2.8mm
Teeth:
Pressing or Milling
Surface:
Only with anti-rust oil; varnish stoving; galvanized; Chrome finish; blueing, etc,
Colors:
natural varnished, red or green varnish, chromated sections or as requested
Use:
All kinds of knife sections suitable for John Deere, New Holland, Claas, Case,Schumacher, Kubota, Yanmar, Ford and so on
Other advantage
End section / half section, which reduces troublesome cutter bar clogging in thick
2. Knife Head:
Material:
iron, steel, rubber
Processing Craft
Forged, machined and casting
Use:
Different kinds of knife heads for
different makes of combine harvesters, swather,lawn mower, like John
Deere, New Holland, Claas,Case and MF.
Application:
According to different working condition, forged, machined and casting quality is available.
Special mould development,according to customers' requirements,based on the sample or drawing
Popular models AH121075, AH89498, AZ50341, 059509P1 and so on.
3. Knife back(Cutter Bar):
Material:
Cold drawn steel
Surface Treatment:
Zinc Plated, Pray Paint, and Powder painting
Length
1930mm, 6000mm, optional
Width
20mm, optional
Thickness
6mm, 7mm,optional
Colour
Black, Natural color
Feature:
The bar with exact measurement holes or without holes will be available
4. Bolt and Nut: can be supply:
Combine Knife Section Knife Section Combine Parts, Knife Section, Pro Cut Knife Section Ningbo Combine Machinery Co.,Ltd. , http://www.combine-harvester-parts.com
Combine Knife Section
2. Teeth: Pressing or Milling.
3. Surface: Only with anti-rust oil; varnish stoving; galvanized;
Chrome finish; blueing, etc. Different surface treatment to protect
against corrosion.
4. Wide variety of sections to fit most applications, smooth, top serrated and under serrated.
5. Hardness: 50-55 HRC, Induction hardening process guarantees long wear.
6. Thickness: 2.00MM; 3MM; 4MM; 5MM; Etc.
Upper serrated and under serrated knife sections with any special teeth number
Different surface treatment to protect against corrosion
and badly tangled crops
â—† Battery maintenance