See Table 1 for the faults and troubleshooting methods when the cone crusher is working. Table 1 Common faults and troubleshooting methods of cone crusher Serial number Fault phenomenon Possible Causes Elimination method 1 Oil pump heating Oil thick or low oil temperature Change oil or warm 2 Oil pump works but low oil pressure 1 suction pipe blockage 2 oil pump gear wear 3 pressure gauge is not allowed Cleaning the oil pipe, replacing the oil pump or pressure gauge 3 The normal working pressure of the oil pump indicates normal but no oil return 1 return oil pipe plug 2 return oil pipe slope is small 3 oil viscosity or low temperature Clean the return pipe, increase the slope, change the oil, and warm 4 No oil or oil flow interruption in the oil level indicator, oil pressure drop 1 tubing plug 2 low oil temperature 3 oil pump is not working properly Cleaning the tubing system Oil heating Check repair pump 5 Reduced oil return and reduced oil in the fuel tank 1 there is a leak under the crusher Oil department 2 rows of oil drains blocked oil Leaking out of the seal Stop inspection to eliminate oil leakage Adjust the amount of oil, clean or deepen the drain 6 The cooler does not work or has little effect 1 no cooling water or insufficient water supply 2 cooling system blockage Open the water gate, normal water supply, check the water pressure gauge, clean the cooler 7 Return oil temperature is too high (>60 ° C) 1The eccentric bushing friction surface produces harmful friction 2 bearing is not working properly 3 oil groove section is insufficient, blocked Shutdown maintenance oil supply, cooling system friction surface, clean 8 There is oil in the water, there is water in the oil 1 cooling water pressure exceeds oil pressure 2The individual water pipes in the cooler are broken, and the water seeps into the oil. The cooling water pressure was made lower than the oil pressure by 0.5 k/cm. , check if the cooler water pipe joint is leaking 9 The drive shaft rotates unevenly, the sound is not normal, the pulley rotates and the moving cone does not move. 1 The gear of the bevel gear is defective in installation, and the axial clearance of the transmission shaft is too large and worn or damaged during operation. 2 pulley or gear key damage 3 unbreakable causes the shaft to break Stop gear change, correct the meshing clearance Replace the spindle and strengthen the iron removal system 10 The crusher is strongly vibrated and the moving cone speed is increased. 1 Oil or no oil between the main shaft and the bushing 2 movable cone sinking or spherical bearing damage 3 tapered bushing clearance is small Stop the inspection to find out the cause Cleaning, refueling Repair or replacement Adjustment gap 11 Increased bulk broken products Movable cone wear Adjust the small discharge port; replace the bracket 12 Great vibration during work Insufficient spring pressure, more fine particles and sticky materials, uneven feeding, insufficient spring elasticity Press or replace the spring, adjust the feed to the mine 13 Hear the crack when turning The lining (moving, fixed) is slack, the screws or earrings are damaged, and the lining is not tight and impacts. Shutdown inspection repair or replacement 14 Water-free in the water seal Water seal water supply pipe is not normal Stop to find out the cause of the water supply interruption weld machine,welding machine,fiber laser welder,fiber laser welding,laser welding machine GUANGZHOU INCODE MARKING TECHNOLOGY CO., LTD. , https://www.gzincode.com
Highlights:
1. Continuous light emission, high electro-optical conversion efficiency, long laser life
2. Maintenance: maintenance-free, adjustment-free, low energy consumption, no consumables, long-term use can save users a lot of processing costs, traditional soldering, argon arc welding, etc., solder, ya gas, iron wire, salt, acid, etc. require a lot of Consumables energy consumption
3. Volume: Small size and compact structure, built-in water cooling, flexible and convenient hand-held welding, and can realize outdoor welding.
4. The operation is simple and easy to learn, and both students and skilled hands can operate on the machine. Under the current situation that it is difficult to recruit skilled workers and the salary cost has doubled, choosing a handheld fiber laser welding machine can easily solve it for you.
5. The work efficiency is high. The traditional marking welding adopts soldering, argon arc welding and other methods, which are low in efficiency and easy to fatigue. The handheld fiber laser welding machine breaks through the traditional practice and is 10-15 times faster than ordinary welding.
6. Hand-held welding head: equipped with 10 meters of imported optical fiber, it can weld a variety of complex welding seam workpieces, large workpieces with irregular shapes, and achieve any angle welding