Model NO.: 905
Origin: Ningbo, China
Electrostatic Powder Coating Spray Gun









Electrostatic Powder Coating Spray Gun




Electrostatic Powder Coating Spray Gun

Electrostatic Powder Coating Spray Gun



Electrostatic Powder Coating Spray Gun
Electrostatic Powder Coating Spray Gun



 
Main data:
Input voltage: AC180V-240V/50HZ
Output high voltage (gun): 0-110KV
Input power: 40W
Weight: 25KG
Air pressure: 0.5Mpa-0.8Mpa
 
Main configuration:
Spray gun * 1 + powder pump * 1 + host * 1+ powder hopper* 1 + trolley * 1 + air pressure control valve * 1+ oil water separator * 1
 
Host For the powder and gas source Spray gun
Input voltage: 200-240v 50Hz Input pressure: ≤0.3Mpa
Input powder: 40W Input pressure: 0-0.6Mpa The volume of the powder: max550g/min
  Output pressure: 0-0.5Mpa Output voltage: 0-100KV
  The largest gas consumption: 13.2m/h (0.4Mpa) Output current: 0-200uA
  Volume of powder barrels: 45L Gun weight:500g
 
 

Cross Roller Bearing is a special type bearing. Because of the inner ring or outer ring were separated, after loading the roller and the cage, it is fixed with the cross roller shaft ring to prevent the separation, so the operation is simple when installing the cross roller shaft ring. Since the rollers are intersected, only one set of cross roller bearings can withstand the load in each direction, which is three to four times more rigid than the traditional model. At the same time, because the inner ring or outer ring of the cross Roller Bearing is a two-part structure, the bearing clearance can be adjusted, and even if it is preloaded, it can obtain a high-precision rotary motion. Moreover, because of its special structure, it is commonly used in industrial robots as joint bearings.

cross roller 1

The classification and model series of cross roller bearings are below:

RB type (outer ring segment)

RB series models for cross roller bearing, basic, inner and outer ring size is minimal to miniaturization, its structure is the outer ring is divided, the inner ring design is an organic whole, the inner ring spinning of high precision parts suitable for requirements.

RE type (inner ring segment)

The RE series is a new type of XRB design concept, which is the same size as the XRB type.The structure of the inner ring is the split type and the outer ring is one design, which is suitable for the parts with high rotating precision of outer ring.

RU type (inner and outer circle)

The RU series model is not required to be fixed flange and support base due to the processing of mounting holes.In addition, due to the adoption of the integrated inner and outer ring structure of the belt, the installation has little effect on the performance, thus achieving stable rotation precision and torque.Can be used for outer ring and inner ring rotation.

RBC type (outer ring segment)

The RBC series model (corresponding to the CRBC series of IKO company) is composed of the outer ring is the split type, the inner ring is one design, and the belt is fully loaded with roller bearings.Suitable for high rotation accuracy of inner ring.

CRBH type (inner and outer ring)

CRBH series model, outer ring and outer ring are integral structure, used for outer ring and inner ring rotation.

RA type (outer circle segmentation, ultrathin type)

The RA series model is the compact type that reduces the thickness of RB and outer ring to the limit.Suitable for areas with light weight and compact design, such as rotating parts of robot and manipulator.

SX type (outer ring segment)

The structure of SX series is similar to that of RB series. The outer ring is a two-part structure, which is designed with three spring card rings and the inner ring, which is suitable for the place where the inner ring has high rotation precision.

XRU08 type (inside and outside)

XSU08 series is similar to the RU series, and the inner and outer rings have been machined with holes, so no fixed flange and support seats are required.Due to the adoption of the integrated inner and outer ring structure, the installation has little effect on the performance, thus achieving stable rotation precision and torque.Can be used for outer ring and inner ring rotation.


We believe that we can supply the best service and price for your, hope to make a long-term cooperation with you. If you have any question please do not hesitate contact with us. We keep warmly welcome you visit us in any time.


Cross Roller Bearing

Cross Roller Bearing,Excavator Parts Cross Roller Bearings,High Precision Cross Roller Bearing,Thin Section Cross Roller Slewing Bearing

LUOYANG AUTO BEARING CO.,LTD , https://www.lyautobearing.com